Mk-diamond MK-377EXP User Manual

10.2014MK-377EXP TILE SAWOWNER'S MANUALOPERATING INSTRUCTIONS & PARTS LISTwww.mkdiamond.comCaution: Read all safety and operating instruction

10MK-377EXP SAW SAFETYWARNINGWARNINGTo reduce the risk of el

11MK-377EXP SAW SAFETYTo avoid the possibility of the applia

12EXTENSION CORD LENGTHNameplate Amperes115V 25' 50' 75' 100' 150' 200'250V 50' 100' 150' 200' 300&a

13SAFETY LABEL LOCATIONSSafety labels contain important safety information. Please read the information contained on each safety label. These labels a

14PRODUCT SPECIFICATIONSThe MK-377EXP is a versatile Tile Saw. Operated and used according to this manual, the MK-377EXP will provide years of dependa

15The MK-377EXP is designed with a rigid frame and removable Cutting Head making the saw easily transportable. To lift the saw, grasp the front and b

16MK-377EXP SAW INSTALLATION(D)Align the Cutting Head Retaining Holes to

17 When installing the Retaining Screw, do not "cross-thread" and DO NOT over tighten the screw.MK-377EXP SAW

18(B)Install the Thumbscrew through the Washer and Splashguard then align to the hole found on back of the Blade Guard and tightenMK-377EXP SAW

19WATER PUMP PREPARATION(B)Connect the Cooling Transfer Tube to the inlet connection of the Blade Guard(A)Press the end of the Cooling Transfer Tube o

2INTRODUCTION Congratulations on your purchase of a MK-377EXP Saw. We are certain that you will be pleased with your purchase. MK Diamond takes pri

20SETUP FOR OPERATION1. Before connecting the MK-377EXP to a power supply, be sure the voltage, cycle and phase meet the requirements of table bel

21MK-377EXP SAW OPERATIONADJUSTMENT & OPERATIONDO NOT FORCE THE

22(D)Fill the Water Pan with clean water(B)Dispose of the contents of the Water Pan and clean the pan. Replace the Cutting Assembly.(A)Ensure the ON/O

23(K)Lubricate the Roller teel Assembly(J)Lubricate the Guide BarTo extend the life of th MK-377EXP, the following procedure should be performed after

24MK-377EXP SAW MAINTENANCE(D)Verify the Movable Cutting Table Roller Whe

25MK-377EXP SAW MAINTENANCEMOTOR BRUSH CHANGE-OUTDisconnect the tool befor

26MK-377EXP SAW TROUBLESHOOTINGTROUBLESHOOTINGBlade will not cut properly.(A)Check f

27"Rodding" cooling channels is performed by inserting a small wire rod through the cooling inlet on top of the Blade Guard and directing th

28MK-377EXP SAW TROUBLESHOOTINGBLADE STOPS TURNING(A)Check the ON/OFF Switch is in

29NOTES

3TABLE OF CONTENTS SAFETYSafety Messages 4 Damage Prevention Message 4 General Safety Precautions 4-7 California Proposition 65 Message 8Electri

30MK-377EXP SAW EXPLODED VIEW 1 2 3 4 5 7 8 10 11 12 13 14 15 17

31MK-377EXP SAW PARTS LISTItem Description Part # Qty 1 HOSE, VINYL

32MK-377EXP SAW EXPLODED VIEW 1 2 3 4 5 6 7 8 9 11 12 13 14 15 1

33MK-377EXP SAW PARTS LISTItem Description Part # Qty 1 FLANGE, O

34MK-377EXP SAW EXPLODED VIEW 1 2 3 6 7 8 2X 152227 BEARING, MULTILUBEIN

35MK-377EXP SAW PARTS LISTItem Description Part # Qty 1 SCREW, H

36MK-377EXP SAW ACCESSORIESITEM 1. MK-200, 7" x 5/8 Arbor 2.

37NOTES

38MK-377EXP SAW ORDERING & RETURNORDERING INFORMATIONYou may order MK Diamond pro

39MK-377EXP SAW CONTACT & WARRANTYCONTACTPlease contact MK Diamond Products, Inc. Cus

4MK-377EXP SAW SAFETYRead and follow all safety, operating a

MK-377EXP TILE SAWOWNER'S MANUAL & OPERATING INSTRUCTIONS MK Diamond Products, Inc.1315 Storm ParkwayTorrance, CA 90501Toll-Free: (800) 421-

5MK-377EXP SAW SAFETYON(())ON(())ON(())All visitors and chil

6MK-377EXP SAW SAFETYConsult the owner’s manual for recommen

7MK-377EXP SAW SAFETYBefore using a power tool, check for da

8MK-377EXP SAW SAFETYSawing, grinding and drilling generate

9MK-377EXP SAW SAFETYWARNINGIn order to prevent electrical sh