Mk-diamond MK-1280 Electric User Manual

www.mkdiamond.comCaution: Read all safety and operating instructions before using this equipment. This owners manual MUST accompany the equipment at a

10MK-1280 ELECTRIC SAW SAFETYUse of under sized extension cords result in low voltage to the motor that can

11The MK-1280 Electric Saw is designed for use with a 16-inch diameter segmented wet or dry MK Dia-mond blade with a .110 to .375 inch cutting width.T

12 MK-1280 ELECTRIC SAW SAFETYThe MK-1280 Saw is equipped with a number of safety decals provided for oper

13MK-1280 ELECTRIC SAW SAFETYSAFETY DECAL LOCATIONSDecal Location DescriptionA Belt Guard Warning - Silica

14MK-1280 ELECTRIC SAW UNPACKINGName addressCitystate zip CodephoNe Faxe-mailproduCt modelpart NumBermaChiNe serial#

15MK-1280 ELECTRIC SAW TRANSPORTThe MK-1280 Electric Saw weighs approximately 185 pounds; two people should be used when trans-p

16MK-1280 ELECTRIC SAW ASSEMBLYMOVABLE CUTTING TABLE INSTALLATIONFig. A While holding the front, position movable

17MK-1280 ELECTRIC SAW ASSEMBLYDIAMOND BLADE INSTALLATIONFig. A Loosen Blade Guard BoltsFig. D Install Retaining Screw and Outer F

18MK-1280 ELECTRIC SAW INSPECTIONThe pre-start inspection should be performed before beginning any job. If the D

19MK-1280 ELECTRIC SAW STARTUPFig. AAttach Vacuum Hose to Vacuum PortDRY CUTTINGSkip step C, if cutting dry.

2We at MK Diamond want to congratulate you on selecting the MK-1280 Electric Saw. We are certain that you will be pleased with your purchase. MK Dia

20MK-1280 ELECTRIC SAW OPERATIONFig. AClean Movable Cutting Table Guide Rails with soap and clean waterEngine part

21MK-1280 ELECTRIC SAW MAINTENANCELike most cutting instruments, a diamond blade performs best when it is dressed. Over

22MK-1280 ELECTRIC SAW MAINTENANCEThe protective wooden strip is to protect the Movable Cutting Table from damage dur

23MK-1280 ELECTRIC SAW MAINTENANCEBELT INSPECTION, ADJUSTMENT AND REPLACEMENTNOTE: 1. When a new belt is installed, it should b

24Turn the ON/OFF switch to the OFF position and place the Fuel Valve in the CLOSED position before performing the following. BLADE WILL NOT CUT PROP

25MK-1280 ELECTRIC SAW TROUBLESHOOTING & CART ASSEMBLYFig. AVerify the motor is running, if not restart (See Setup, Start-up, Adjustm

26MK-1280 ELECTRIC SAW CART ASSEMBLYFig. APlace handle in the middle of tow bracket. Slide one washer on to bolt and slide through h

27MK-1280 ELECTRIC SAW CART ASSEMBLYFig. ATo set brake press “on” the lever on back castersSETTING BRAKENOTES: The wheels and caste

28NOTES

29NOTES

3SAFETY PageSafety Message/Alert Symbols, Warnings 4-5Hazard Symbols 5General, Maintenance, Saw Safety 6-7California Proposition 65 Message 7Electrica

30MK-1280 ELECTRIC SAW EXPLODED VIEWFIGURE 1 - MK-1280 PAVER SAW - P/N 167492

31ITEM DESCRIPTION PART# QTY1 NUT, 3/8 16 HEX 101188 72 NUT, HEX, 5/16 - 18 101196 83 WRENCH, 3/4 BOX END 134056 14 KEY, 3/16 SQ X 1-1/8 150344 15 SCR

32MK-1280 ELECTRIC SAW EXPLODED VIEWFIGURE 2 - MK-1280 PAVER SAW - P/N 166561

33FIGURE 2 - MK-1280 PAVER SAW - P/N 166561MK-1280 ELECTRIC SAW PARTS LISTITEM DESCRIPTION PART# QTY43 OWNERS MA

34MK-1280 ELECTRIC SAW PARTS LISTITEM DESCRIPTION PART# QTY1 WHEEL, CONVEYOR CART 133090 42 SCREW, HEX HD, 1/4

35MK-1280 ELECTRIC SAW PARTS LISTITEM DESCRIPTION PART# QTY1 KEY, 3/16 SQ X 1 - 1/8 150344 12 BEARING, ARBOR HOU

36MK-1280 ELECTRIC SAW PARTS LISTITEM DESCRIPTION PART# QTY1 ELBOW, 1/4 MNPT STREET 154615 12 FITTING,

37MK-1280 ELECTRIC SAW PARTS LISTFIGURE 6 - ASSY, CART - P/N 167437ITEM DESCRIPTION PART# QTY1 NUT, 3

38NOTES

39MK-1280 ELECTRIC SAW ORDERING & RETURN INSTRUCTIONSORDERING INFORMATIONYou may order MK Diamond products through you

4 MK-1280 ELECTRIC SAW SAFETYRead and follow all safety, operating and maintenance instructions. Failure t

MK Diamond Products, Inc.1315 Storm ParkwayTorrance, CA 90501Toll-Free: (800) 845-5830Phone: (310) 539-5221Fax: (310) 539-5158www.mkdiamond.comMK-128

5MK-1280 ELECTRIC SAW SAFETYIf using an extension cord make sure it is in good condition first. When usi

6MK-1280 ELECTRIC SAW SAFETYSawing and drilling generates dust. Excessive airborne particles may cause irritation

7MK-1280 ELECTRIC SAW SAFETYConsult the owner’s manual for recommended accessories. Using improper access

8ELECTRICAL REQUIREMENTS AND GROUNDING INSTRUCTIONSIn order to prevent potential electrical shock and injury, the following electrical safety precauti

9 Supporting Surface Power Tool Drip Loop Power Cord Drip Loop InformationTo avoid the possibility of the appliance plug or receptacle gettin