09.2011BX-3 MASONRY SAW OWNER'S MANUAL, PARTS LIST &OPERATING INSTRUCTIONSCaution: Read all safety and operating instructions before using th
10Use of under sized extension cords result in low voltage to the motor that can result in motor burnout and premature failure. MK Diamond warns that
11SAFETY LABEL LOCATIONS: Safety labels are located according to Figures 1 to 4 below. The labels contain important safety information. Please read
12PRODUCT SPECIFICATIONS: The BX-3 is a versatile lightweight, dry, masonry saw. Operated and used according to this manual, the BX-3 will provide ye
13UNPACKING: Your BX-3 has been shipped from the factory thoroughly inspected. Only minimal assembly is required. If not already done, remove the BX-
14ASSEMBLY:Follow the assembly instructions to prepare your BX-3 for operation.1. Movable Cutting Table Installation: 2. Adjustable Cutting Guide In
15SETUP:• Before powering or starting, check for damage that could prevent this equipment from proper operation or performing its intended function.
16If an extension cord is used, first verify it meets the requirements of TABLE 1 (page 9). Plug the BX-3 into the extension cord; plug the extension
17ADJUSTMENT AND OPERATION:1. Cutting Setup: DO NOT FORCE the blade to cut, it will do the job better and safer at rate for which it was designed. 2.
183. Chop Cutting: A Chop Cut is performed by cutting completely through an object in one pass. 4. Cutting with the Cutting Head Locked Down: This m
195. Angle Cuts: Angle Cuts may be performed using the Step Cut, Chop Cut or the Locked Cutting Head cutting methods. The following is utilizing the
2Congratulations on your purchase of a Diamond Vantage Tile Saw. We are certain that you will be pleased with your purchase. We take pride in produci
206. Cleanup: Always wear eye protection when using compressed air. (B)Unplug GFCI from BX-3 (C) Remove Motor Filter Cap (A)Unplug GFCI from Power So
21MAINTENANCE:1. General Maintenance: The following maintenance should be performed following each use. Use Light oil, such as WD-40 or 3 in 1 when
223. Blade Dressing: Like most cutting instruments, a diamond blade performs best when it is dressed. Over time and use, diamonds on the outer edge
23BX-3 MAINTENANCE4. Diamond Blade Change-out: Disc
245. Movable Cutting Table Wheel Change Out: NOTE: All four (4) Movable Cutting Table, Roller Wheels should be replaced at the same time (MK Diamond
256. Protective Wooden Strip Replacement: The protective wooden strip is to protect the Movable Cutting Table from damage during operation. Over tim
267. Motor Brush Change-out: Disconnect the tool before servicing and when changing accessories, such as blades, bits, cutters, and the like. NOTE:
27TROUBLESHOOTING:Verify the Lockable Switch is unlocked and the saw is disconnected from the power source before performing any troubleshooting proce
283. Movable Cutting Table Does Not Move Correctly: (A)Check Guide Rails Clean (C) Verify Ease and Freedom of Movement If Clean, go to Step B If Dirt
29BX-3 EXPLODED VIEW
3TABLE OF CONTENTS SAFETYSafety Message/Alert Symbols Damage Prevention MessageGeneral Safety Precautions and Hazard Symbols California Proposition 6
30PARTS LIST: n/p KM ytQ noitpircseD metI a/n 1 thgiR ,emarF ,ylbmessA A 763751 1 thgiR ,emarF ,gnitsaC 1A 963751 1 tfeL ,emarF ,gnitsaC 2A 483751 3 e
31 n/p KM ytQ noitpircseD metI 601851 1 rennI ,egnalF 3E 701851 1 egnalF xeH mm02 x 5.1 – 01M ,wercS 4E 851851 4 paC daeH xeH mm02 x 1-6M ,wercS 6E 95
32THEORY OF DIAMOND BLADES:Diamond blades do not really cut; they grind the material through friction. Diamond crystals, often visible at the leading
33ACCESSORIES AND REPLACEMENT PARTS: NOITPIRCSED REBMUN METI1. 157957 MK-BX10, Dry Cutting 14" Segmented Blade 2. 157944 MK-BX30, Dry Cutti
34BX-3 ORDERING AND RETURN INFORMATIONORDERING INFORMATIONYou may order MK Diamond products through your local MK Diamond distributor or, you may ord
35BX-3 CONTACT AND LIMITED WARRANTYCONTACT:Please contact MK Diamond Products, Inc. Customer Service Department with any questions you might have reg
MK-101 Pro 24 Tile SawOWNERS MANUAL & OPERATING INSTRUCTIONDOCUMENT NO. 158808MK Diamond Products, Inc.1315 Storm ParkwayTorrance, CA 90501Toll-Fr
4Read and follow all safety, operating and maintenance instructions. Failure to read and follow these instructions could result in injury or death to
5If using an extension cord make sure it is in good condition first. When using an extension cord, be sure to use one heavy enough to carry the curren
6Consult the owner’s manual for recommended accessories. Using improper accessories may increase the risk of personal or by-stander injury. Serious i
7Sawing and drilling generates dust. Excessive airborne particles may cause irritation to eyes, skin and respiratory tract. To avoid breathing impai
8ELECTRICAL REQUIREMENTS AND GROUNDING INSTRUCTIONSIn order to prevent potential electrical shock and injury, the following electrical safety precauti
9 Supporting Surface Power Tool Drip Loop Power Cord Drip Loop InformationTo avoid the possibility of the appliance plug or receptacle gettin
Comments to this Manuals